mae00001gem mn102l59d type mn102l59d MN102LF59D internal rom type mask rom flash rom (byte) 64k ram (byte) 2k package (lead-free) lqfp064-p-1414 lqfp064-p-1414 (es (engineering sample) available) minimum instruction execution time [with main clock operated] 100 ns (at 4.5 v to 5.5 v, 5 mhz externally, multiplied by 4 internally) ? interrupts reset, watchdog, timer counter 0 to 11, external 0 to 5, serial ch.0 tra nsfer ? nish, serial ch.1 tra nsfer ? nish, /nmi pin, a/d conversion ? nish ? timer counter timer counter 0 : 8-bit 1 (timer output, event count) clock source ................ 1/1, 1/64, 1/128 of system clock frequency; external clock interrupt source ........... under? ow of timer counter 0 timer counter 1 : 8-bit 1 (timer output, event count, a/d conversion start up) clock source ................ 1/1, 1/64 of system clock frequency; external clock; timer counter 0 output interrupt source ........... under? ow of timer counter 1 timer counter 2 : 8-bit 1 (timer output, event count) clock source ................ system clock; external clock; timer counter 0, 1 output interrupt source ........... under? ow of timer counter 2 timer counter 3 : 8-bit 1 (interval timer, uart baud rate generator) clock source ................ 1/1, 1/2, 1/64 of system clock frequency; timer counter 0 output interrupt source ........... under? ow of timer counter 3 timer counter 4 : 8-bit 1 (interval timer) clock source ................ 1/1, 1/64, 1/128 of system clock frequency; timer counter 0 output interrupt source ........... under? ow of timer counter 4 timer counter 5 : 8-bit 1 (interval timer) clock source ................ 1/1, 1/64 of system clock frequency; timer counter 0, 4 output interrupt source ........... under? ow of timer counter 5 timer counter 6 : 16-bit 1 (timer output, event count) clock source ................ 1/1, 1/128 of system clock frequency; external clock; timer counter 0 output interrupt source ........... under? ow of timer counter 6 timer counter 7 : 16-bit 1 (timer output, event count) clock source ................ 1/1, 1/128 of system clock frequency; external clock; timer counter 0 output interrupt source ........... under? ow of timer counter 7 timer counter 8 : 8-bit 1 (timer output, event count, simple pwm output) clock source ................ 1/2, 1/8 of system clock frequency; external clock; timer counter 0 output interrupt source ........... under? ow of timer counter 8 timer counter 9 : 8-bit 1 (timer output, event count, simple pwm output) clock source ................ 1/2, 1/8 of system clock frequency; external clock; timer counter 0 output interrupt source ........... under? ow of timer counter 9 timer counter 10 : 8-bit 1 (timer output, simple inverter control [simple 6-phase pwm output]) clock source ................ high-speed clock (after multiplication); 1/1, 1/2, 1/8 of system clock frequency interrupt source ........... over? ow of timer counter 10 timer counter 11 : 16-bit updown counter 1 (highly functional inverter control [simple 6 -phase pwm output], a/d conversion start) clock source ................ high-speed clock (after multiplication); 1/1 of system clock frequency interrupt source ........... over? ow of timer counter 11 ; under? ow of timer counter 11 connectable timer counter 0, 1, 2 timer counter 0, 4, 5
mae00001gem mn102l59d ? serial interface serial 0, 1 : 1 to 8-bit 1 (common use with half-duplex uart, transfer direction of msb/lsb selectable) clock source ................ 1/2, 1/4, 1/16 of system clock, 1/2 of timer counter 3, external clock half-duplex uart 2 (common use with serial 0, 1) ? i/o pins i/o 52 common use : 52 (by bit) ? a/d converter 10-bit 12-ch. (with s/h) : 4 channels for common use ? pwm 16-bit 2-ch. (commen use with timer counter 6,7) simple 6-phase pwm output 8-bit 1-ch.(common use with timer counter 10) 6-phase pwm output 16-bit 1ch. (timer counter 11 ) ? notes 6 -phase pwm output support ? electrical charactreistics (supply current) parameter symbol condition limit unit min typ max operating supply current iddopr vi = vdd or vss, output open f = 5 mhz , vdd = 5.0 v 75 ma supply current at stop idds pin with pull-up resistor is open all other input pins and hi-z state input/output pins are simultaneously applied vdd or vss level f = 5 mhz , vdd = 5.0 v, output open 50 a supply current at halt 0 iddh 30 ma (ta = C 20 c to +85 c, vdd = 5.0 v, vss = 0 v) ? development tools in-circuit emulator px-ice 102l00 + px-prb102l59-lqfp064-p-1414 ? pin assignment 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 p70, buzz p71 p72 p73 p74 p75 p76 p77, wdout vss /rst vss sysclk vdd osci osco vdd p37, an0 p36, an1 p35, an2 p34, an3 p33, an4 p32, an5 p31, an6 p30, an7 p57, an8 p56, an9 p55, an10 p54, an1 1 p53 p52 p51 p50 p25, /irq5 p24, /irq4 p23, /irq3 p22, /irq2 p21, /irq1 p20, /irq0 p16, tmio6 p15, tmio5 p14, tmio4 p13, tmio3 p12, tmio2 p1 1, tmio1 p10, tmio0 p02, sbo0 p01, sbi0 p00, sbt0 p40, pwm0, tmio0 p41, /pwm0, tmio1 p42, pwm1, tmio2 p43, /pwm1, tmio6 p44, pwm2, tmio7 p45, /pwm2, st op p60, tpwm0, sbt0 p61, tpwm1, sbi0 p62, tpwm2, sbo0 p63, tpwm3, sbt1 p64, tpwm4, sbi1 p65, tpwm5, sbo1 vdd /nm i mn102l59d lqfp064-p-1414 note) the MN102LF59D is manufactured and sold under license agreement with bull cp8 inc. note that MN102LF59D cannot be used as the ic card.
request for your special attention and precautions in using the technical information and semiconductors described in this book (1) if any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) the technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) the products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod- ucts may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this book are subject to change without notice for modification and/or im- provement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (esd, eos, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. when using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) this book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. industrial co., ltd.
|
